The Voluntary Sector Initiative is reader-supported. When you buy through links on our site, we may earn an affiliate commission. Learn more

Top 10 Cheap Tiny Whoop of 2020 – Consumer Guide & Reviews

Rank No. #1
Crazepony 3pcs FPV Camera Mount Inductrix Tiny Whoop for Quadcopter Camera FX798T FX797T Eachine EF-01 Camera
  • 【Light weight】This fpv canopy weights at 23g. It will not burden the camera body
  • 【Widely useful】20 degree mount Works well with the 1.8 lense on these cameras.
  • 【Camera bracket】This is a Camera/VTX mount for the Blade Inductrix. Only fit for FX798T FX797T MC-01 camera.
  • 【Easy installation】All stock hardware is used, super simple installation. Just remove the front, and 2 side Flight Controller Screws, press them into the mount, and reassemble.
  • 【Stable structure】It holds the camera securely and eliminates the chance of tearing a SMD component of the board with aggressive double sided tapes
SaleRank No. #2
Crazepony 4pcs 615 Coreless Motor Special Sauce Edition for SNAPTAIN SP350 Blade Inductrix Tiny Whoop
  • Special Sauce Edition 17500kv @3.7V / 65,000 rpm
  • Shaft Diameter: 0.8mm, Motor Diameter: 6mm, Motor Length: 15mm, With 1.25mm JST Plug
  • Weight: about 1.8g, Quantity: 4 pcs (2 CW and 2 CCW)
  • Work for Blade Inductrix, Tiny Whoop, Nano QX etc.
  • Deliver high efficiency and constant power for a stable flight
Rank No. #3
1S LiPo Battery USB Charger 3.7V/4.20V 6 Channel 1S LiPo Charger Tiny Whoop Blade Inductrix Micro JST 1.25 JST-PH 2.0 mCX mCPX Connectors
  • ONLY support LiPo 3.7V/4.20V 1S battery
  • Support 0.2A/0.6A charge current by switch button ( Suggest using 0.2A if you charge six at the same time and 0.6A if you only do 2)
  • USB interface input suggested range: 5V±5% on 0.5-2.4A, suggested 2.4A or above
  • Charger plug: Micro 1.25 and JST-PH 2.0, AKA mCX and mCPX, Charging max 6 batteries at the same time. ( Need to consider width of battery)
  • The 6 LED lights indicate the charging state of the six channels independently, LED solid indicates charging, LED off indicates full charged.
Rank No. #4
Gaoneng 6pcs 380mAh HV 1S Lipo Battery FPV Battery 60C/120C 3.8V with PH 2.0 Powerwhoop Connector for UZ65 US65 Tiny Whoop Drone Blade Inductrix
  • High capacity of 380mah 60C, Small size of 62 * 11 * 7mm, is the great choice of Tiny Whoop Blade inductrix
  • The battery connector is PH 2.0 AKA High current ultra micro, Powerwhoop, mCPX
  • This 380mah HV 1S Lipo Battery gives an increase in performance, provide you more punch and longer flight times and only weight 8g per unit
  • GAONENG 380mah Battery is Great for brushed whoop motors of any size and brushless 1s and 2s whoops as well. Like snapper 7, betafpv6s, mobula 7, Beta65s, beta65x
  • Caution: As a FPV battery, Don't over-charge, or over-discharge batteries. Don't put it beside the high temperature condition. Don't throw it into fire. Don't throw it into water
Rank No. #5
20pcs 31mm Propellers Prop CW CCW Sets Replacement Parts for FPV Racer Tiny 6,Tiny Whoop,Eachine E010,E010C,E010S,JJRC H36,Blade Inductrix FPV Drone Racing Quadcopter DIY
  • 20pcs Replacement Propellers, CW CCW,31mm 0.8mm Mounting Hole 4-Blade ,Durable
  • Compatible with FPV Racer Tiny 6,Tiny Whoop,Eachine E010,E010C,E010S,JJRC H36,Blade Inductrix
  • Light weight,smaller inertia,more violent,the Weight only 0.462g/pcs
  • Center Hole: 0.8mm, Prop Diameter: 31mm,Hub Thickness: 9.43mm
  • This is the best for your choice to DIY your Drone.
Rank No. #6
AKK 1S LiPo LiHV Battery Charge Board Micro JST 1.25 and JST-PH 2.0 2-6S Input LiPo Battery Drone Charger for Blade Inductrix Tiny Whoop
  • XT60 2S-6S LiPo or DC 12V/3A adapter
  • LED indicator clearly shows your batteries charging status
  • Support LiPo and LiHV batteries by a voltage switch: 4.2V for LiPo, 4.35V for LiHV
  • 6 independent charging ports: 0.2/0.6A & 4.2/4.35V swichable for each set of port.
  • Output connectors: Micro JST 1.25, JST-PH 2.0 (and Micro Losi and JST by the cables), compatible with most batteries.
Rank No. #7
BETAFPV 100pcs Screw Rubber Damper Set M1.2x4 Screw M1.4x5 Screw Rubber Damper for Tiny Whoop FPV Racing Quadcopter
  • 【Application】Those screws and rubber dampers are really useful when you are mounting flight controller board to your whoop drones
  • 【M1.2x4 &M1.4x5 】M1.2* 4 screws fit for stock Blade Indcutrix frame / 65mm frames. M1.4* 5 screws fit for Eachine black E010 frame / 75mm / 85mm frames
  • 【Black &Blue Rubber Damper】Black rubber dampers has a gap of 0.8mm, suitable for ALL brushed FC boards. Blue rubber dampers has a gap of 1.8mm, suitable for 2-4S AIO FC boards
  • 【White Rubber Damper】White rubber dampers has a gap of 1.2mm, suitable for 2S AIO FC boards, F405 FC stack etc.
  • 【Package】Package is including 20 * M1.2x4 screws, 20 * M1.4x5 screws, 20 * blue rubber damper, 20 * black rubber damper, 20 * white rubber damper
Rank No. #8
BETAFPV Beta65S Tiny Brushed Whoop Drone 1S Frsky FPV Quadcopter with M01 AIO Camera F4 1S Brushed FC 25mW 716 19000KV Indoor FPV Drone
  • 【EQUIPMENT】Beta65S has been upgraded F4 Brushed Frsky FC with M01 AIO Camera 5.8G VTX with 7x16mm brushed motors.
  • 【MOTOR SYSTEM】7x16mm 19000KV Brushed Motor, power system can support the smooth flight of the drone, bring you a perfect flight operation experience.
  • 【SECURE & DURABLE】The structured style and four propeller brackets ensure safe flight which protects you to avoid body injury from spinning propellers. ABS material can withstand countless crashes or drop,compatibale with beginners.
  • 【TINY and EASY CARRY】Small sized drone Beta65S is the perfect indoor drone makes it to easily operate around smaller spaces designed to be compact and portable right into your pockets,the first chioce for beginners.
Rank No. #9
BETAFPV Beta85 Pro 2 2S Brushless Whoop Frsky with F4 AIO 2S FC 11000KV 1103 Motor C01 Camera for Tiny Whoop FPV Acro Racing
  • 【F4 AIO 2S FC】Equipped with F4 1-2S AIO brushless FC with an integrated 25mW VTX, saving the drone's weight to 40.4g without battery
  • 【1103 11000KV Motor】1103 11000KV motorsJust plug and play connector. Without soldering or tinkering necessary
  • 【C02 Micro Camera 】Miniature, and lightweight design, weight at only 1.4g, best for saving drone's weight
  • 【Durable Frame&Props】With durable and light enough frame for 85mm whoop. Washout issue almost doesn't exist with Gemfan 2020 4-Blades Props
  • 【Lighter, powerful for fpv racing】Beta85 Pro 2 only weighs 40.4g without battery, perfectly suitable for FPV racing
Rank No. #10
AKK BA3 5.8G 40CH VTX 0/25mW/50mW/200mW Switchable 600TVL 1/3 Cmos Micro AIO FPV Camera and Transmitter for FPV Drone Like Tiny Whoop Blade Inductrix
  • AIO FPV camera+transmitter+brass dipole atnenna all 3 functions in one limit size and weight. weight:4.7g
  • Output power 25mW/50mW/200mW Switchable, Compatible with 5.8GHz googles and monitor.
  • Requires 1S LiPo battery, Signal Range Suitable for Ultra Micro RC Aircraft.
  • Upgraded low-light condition for flying in dimmer light.
  • Power level switchable, designed for all ranges of flying both indoor or outdoor.
Rank No. #11
BETAFPV 3 Sets 7x16mm Motor 19000KV Brushed Motors with Jst1.25 Connector for Micro FPV Tiny Whoop Beta65S Frame and Eachine E011 Frame
  • The most powerful 7x16mm motors are upgraded from 17500KV to 19000KV. We are sure that these motors will turn your micro whoop into powerful monster.
  • Weight is 2.95g per motor (including cables and connector); Size: 7x16mm
  • With JST 1.25mm 2-Pin connector, perfect for Blade Inductrix, Tiny Whoop flight controller
  • These 7x16mm motors only fit for BETAFPV Beta65S frame and Eachine E011 frame for the moment. It does not fit the regular Whoop frames.
  • Package: 3 SETS * 7x16mm 19000KV motors (6CW +6CCW)
Rank No. #12
BETAFPV F4 FC 1S Brushed Flight Controller with SPI Frsky Receiver OSD Smart Audio for FPV Tiny Whoop Micro Racing Drone
  • The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.
  • The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups
  • F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. Upgraded to 30A Lower Resistance MOSFET, Firmware version: betaflight_matekf411rx_3.4.0. Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support Smart Audio.
SaleRank No. #13
4pcs 550mAh HV 3.8V 1S LiPo Battery 50C JST-PH 2.0 PowerWhoop mCPX Connector Rechargeable 1S LiPo Battery for Inductrix FPV Plus Eachine trashcan Tiny 7 Beta75 75 Pro Tiny Whoop FPV Racing Drones
  • Capacity: 550mAh 50C 3.8V,the 550mAh large capacity offers you a long flying time.
  • Light weight reliable,50C Discharge Rate,High-grade Lipo cell is highly reliable and durable for long-lasting use.
  • To fit for Tiny 7, Tiny 8X, Mobula 7, Snapper7, Inductrix FPV Plus, Inductrix FPV BL, Eachine trashcan, Beta75, Beta75 Pro Tiny Whoop FPV Racing Drones. NOT for Inductrix FPV
  • The connector plug: JST-PH2.0 AKA High current ultra micro, Powerwhoop, mCPX.
  • Newly developed chemistry HV 1S Battery, Much more Safer, higher quality and more poewrful rate gives you higher speed flying experience.
Rank No. #14
GAONENG 6pcs 380mAh 60C 1S LiPo Battery 3.8V/4.35V LiHv Battery with JST-PH 2.0 Connector for UZ65 Tiny Whoop Micro FPV Racing Drone
  • The ultra 380mAh 1S LiPo Battery for Tiny Whoop Blade Inductrix(Need PH2.0 Upgrade)Quadcopter.
  • Battery Size:62*11*7.0mm, Weight: 8g/per unit, Connector: PH 2.0 AKA High current ultra micro, Powerwhoop, mCPX
  • The weight of the 380mAh 1S Lipo battery is 0.7g heavier than the 300mAh battery, better performance than it.
  • Newly developed chemistry 380mAh 1S Lipo Battery, high voltage gets longer flight time and safer charging situation.
  • Note: Don't over-charge, or over-discharge batteries. Do not use inferior chargers. Don't put it beside the high temperature condition. Don't use high current charging frequently.
Rank No. #15
BETAFPV Gemfan 16pcs 31mm 3-Blade Propellers with 1.0 mm Shaft Hole Micro Whoop Drone Propellers for Tiny Whoop FPV Racing Whoop Like Meteor65 Quadcopter
  • 【Material&Colors】Made of PC material, durable and more power violent. Comes with 4 colors including white, transparent blue, transparent yellow and transparent purple
  • 【Compatible Drones】31mm 3-blade props are an available option for BETAFPV Meteor65, Beta65 Pro, Beta65X etc
  • 【Suitable Motors】Perfect match with 0802 22000KV motors, you will get completely different powerful and smooth flight experience of 1S brushless racing whoop
  • 【Weight&Size】Only weighs 1.0g/set. 31mm 3-blade propellers with 1.0mm shaft inner diameter
Rank No. #16
Crazepony 4pcs 6x15mm Motor (Speed: Insane) 19000KV for Blade Inductrix Tiny Whoop Micro JST 1.25 Plug
  • Speed: insane, 19000kv / 70000 rpm
  • With 1.25mm JST Plug, perfect for Inductrix FC
  • Weight: 1.8g each , Quantity: 4 pcs (2 CW and 2 CCW)
  • Insane for Blade Inductrix, Tiny Whoop, Nano QX etc
  • Shaft Diameter: 0.8mm, Motor Diameter: 6mm, Motor Length: 15mm, Cable Length: 56mm
SaleRank No. #17
4pcs 600mAh 1S 3.7V LiPo Battery 50C JST-PH 2.0 PowerWhoop mCPX Connector Rechargeable 1S LiPo Battery for Inductrix FPV Plus Tiny Whoop FPV Racing Drone
  • ★Capacity: 600mAh 50C 3.7V,the 600mAh large capacity offers you a long flying time.
  • ★Light weight reliable,50C Discharge Rate,High-grade Lipo cell is highly reliable and durable for long-lasting use.
  • ★To fit for Mobula 7 HD Snapper7 Tinyhawk Freestyle Race Beta75 Pro Beta75S Eachine M80 Trashcan Kingkong Tiny 7 Inductrix FPV Plus 75mm FPV Racing Drone .NOT for Inductrix FPV
  • ★The connector plug: JST-PH2.0 AKA High current ultra micro, Powerwhoop, mCPX.
  • ★Newly developed chemistry 1S Battery, Much more Safer, higher quality and more poewrful rate gives you higher speed flying experience.
Rank No. #18
BETAFPV Meteor65 1S Brushless Whoop Frame Kit Blue Orange with 2 Sets 31mm 3-Blade Props 1.0mm Shaft White for 65mm Meteor65 1S Brushless Micro Tiny Racing Whoop Quadcopter
  • 【Battery Slot Updated】Compared to previous 65mm brushless frames, with the low profile of battery slot height, the drone's gravity center is reduced and improved the sense of compactness
  • 【Motor Mounting Position】Meteor65 1S brushless frame’s motor mounting position uses triangle bilateral stretch structure, makes frame more aesthetic. Provides pilots more durable and smoother flight experience
  • 【Weight&Ultra Lightweight】The ultra light and durable frame is PP material only 3.08g, which is one of the lightest frames with a 26mm*26mm FC mounting columns can match whoop style flight controller
  • 【31mm 3-Blade Props】The material of 31mm 3-blade props is PC plastic with the 1.0mm shaft inner diameter. Suitable for 0603 and 080X series brushless motors
Rank No. #19
BETAFPV Backpack Carrying Case Blade Inductrix Storage Box with Foam Liner for Tiny Whoop Eachine E010 etc
  • This backpack carrying case bag is suitable for Tiny Whoop Beta65, Beta75, Blade inductrix, Eachine E010 etc, and 260mAh battery.
  • With strong high density foam Liner to keep your quadcopter safe and secure, and the outer case uses water-proof material
  • Compact black case for the protection of your new drone
  • Dual zip closure offers extra security for the protection of your drone
  • Includes an interior netted storage compartment for additional accessories
Rank No. #20
Rlfearl 10pcs Upgraded Tiny Whoop JST-PH 2.0 Male and Female Connector Cable for Battery JJRC H36 H67 Blade Inductrix E010 E013
  • 5Pairs,Including 5pcs male connector cable and 5pcs female connector cable
  • Upgrade JST-PH 2.0 connector, the pins will not loose easily
  • Must have for HV batteries and high performance
  • 80mm length/per unit. 22AWG soft silicone wire
  • Suitable for tiny whoop like JRC H36 H67 Upgrading Blade Inductrix, E010 E013, and KingKong Tiny drone

Last update on 2021-07-30 / Affiliate links / Images from Amazon Product Advertising API

We’ve made a buying guide of top 10 Cheap Tiny Whoop for our consumer to review. The reports above show ratings of the best overal, best cheap Cheap Tiny Whoop to buy in 2020.

If you think there is mislead information on any products and services, feel free to contact our experts at any time.